Search results
-
Scale 20cc Edge 540 Profile “The Glitter”
Break out the gopro when you get her in the air!!- Stevendavis
- Post #646
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Any flites yet Snoopy??- Stevendavis
- Post #644
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Thanks Snoopy! Covering make take a while! It's not one of my favorite jobs.- Stevendavis
- Post #643
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Got some work done on the other wing panel.- Stevendavis
- Post #641
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Thanks Snoopy!- Stevendavis
- Post #640
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Parts are ready!- Stevendavis
- Post #638
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Hey snoop, I'm taking my time as much as possible. Hopefully this lockdown stuff will end soon. One good thing about no school is I can use the parking lot to get some flying in!!- Stevendavis
- Post #637
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
finished up a few more details on the wing panel before setting it aside and starting on the other. I added some doublers for the hinges, as well as an anti rotation pin block, and some doublers for the servo opening. I also got the aileron built.- Stevendavis
- Post #635
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Got the tube doublers cut and installed. Also got the wire access done in the ribs. The tube is just set in place, as I will not glue it in until I mount the wings on the fuse and make sure the tube is exactly where it needs to be, then I'll glue the top sheeting on. This one is about ready to...- Stevendavis
- Post #634
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Will do, and thanks!- Stevendavis
- Post #633
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
That info helps!! Thanks Balsa! One more question here, did you add any re-enforcement around the wing tube, or just use the ribs?? Thanks- Stevendavis
- Post #631
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Thanks Snoop!! I know I'm probably making a few mistakes on this one. The next one will be better, once I figure out every thing I need to change on this build. I'm in the process of putting together an assembly manual, to work every thing out. I'm hoping to at least keep it below 7.5 lbs. If I...- Stevendavis
- Post #630
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Decided to go with 1/8" X 4" balsa sheer webbing.- Stevendavis
- Post #627
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Thanks Balsa! I was thinking about that once I put that trailing edge piece on! I'm using 1/16" sheeting, and was thinking I should have used something a tad thicker. 1/16 is a bit soft. What is recommended?- Stevendavis
- Post #626
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Changed my other mind! I'm going to leave the SFG's off of this one and go with stock wings. Working on wing #1, or the right wing, and got ahead of myself. I didn't open up rib 1 and 2 for wire access, but It's not a big deal to dermal them out now. Now I just have to configure the equipment...- Stevendavis
- Post #624
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Got a little more work done!- Stevendavis
- Post #623
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
I hear what your sayin! I'll probably build the mounts in, and try it both ways to see what I like better. I know the ProX really benefits from them. Hopefully the Glitter is a beast without them!- Stevendavis
- Post #622
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
That's definitely a thought!- Stevendavis
- Post #621
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
I hear ya Snoop, I do think they help with tighter knife edge loops, easier hairiers, and slower landings. Just more over all stability. I'm in the process of making a template for them. I'll have to make rib 7 out of ply though!- Stevendavis
- Post #617
- Forum: Giant / Scale Scratch and Kit Build Threads
-
Scale 20cc Edge 540 Profile “The Glitter”
Like the side by side Snoop! I'm thinking of adding side force generators on this one also!- Stevendavis
- Post #615
- Forum: Giant / Scale Scratch and Kit Build Threads